Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths who have the right equipment and technical know-how to get a new peugeot car key. They can program and create keys quicker and more efficiently than a dealership.

If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are many other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery can hinder your Peugeot 208 from locking or unlocking, and will not start the engine. In this case you'll have to make use of the alternative method for starting that is described in the owner's manual.

The spark plugs may also be worn out. The spark plugs are responsible for sparking the fuel that powers the engine. However they have a short lifespan. They will eventually break down if they aren't used frequently enough.

There is an easy solution to this problem. Check the voltage of the battery using a multimeter. If the voltage is below 11,5 volts, it's the time to replace it. If the battery is corroded it is crucial to clean its contacts. This can be accomplished by removing the rubber covers from the two terminals on the battery and then using a wirebrush to eliminate any parts of the battery that are corroded. Then, reconnect the cables to the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery hasn't failed, you should look at the spark plugs. It could be that they're overly dirty, which causes them not to spark. The spark plugs can be cleaned in the workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.

Water damage is the most common reason for this issue. This is most common in colder climates where the vehicle may have been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who has all of the tools and equipment required to change the key's programming. They will also have the latest technology and machinery required to make a Peugeot smart key. The process shouldn't be more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the transponder chips using a new type that uses electronic components that are mounted on a circuit board. The new system is fantastic when it's new, but the circuit boards deteriorate over time and stop working properly.

This can stop the immobiliser chip activating the immobiliser chip, causing your car not to start. If this is the case it's recommended to contact a peugeot key code specialist or locksmith.

Another issue that is common is when the key fob battery is dying, this causes the key blade to stop getting into the lock. A locksmith for cars will replace the battery and then cut a new blade for you. This is a simple solution.

Faulty Receiver Module

It could be that the receiver module is faulty when your Peugeot key fob isn't working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for transmitting radio frequency signals to the on-board computer, which controls the central locking system inside your Peugeot vehicle.

The key fob itself is fitted with rubber seals that block water from getting to the electronic chip inside. However prolonged exposure to water may cause damage to these seals and the chip. Submerging the key fob into sea water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.

If your Peugeot spare key fob doesn't work, you'll need to have the module replaced. This can only be done by an Peugeot Key Replacement Cost specialist or a professional auto locksmith. Like other automobiles, Peugeot keys are protected by an unique immobilizer system that requires the correct coding to start the engine. This is why you must be able to trust a professional Peugeot locksmith for the job of programming and creating an appropriate replacement.

Computer on-board is not working properly

The on-board computer of your Peugeot is responsible for various features in your car, including power windows and airbags. If something goes wrong with these systems, it will typically show a code that identifies the problem. This code is saved in the system and stays there until the problem is resolved. Often, this will involve replacing the computer on board.

The most frequent cause for the airbag warning light to flash is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. This issue needs to be addressed as soon as you can, since an airbag that is not functioning could pose a risk in the event of an accident.

If your peugeot 107 key fob is showing a card detected as not present error, then the battery in the key fob could be weak or dead. This will stop the key fob sending a signal that will disable the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this fails it is likely that the battery is in need of replacement.