How to Replace a Kia Sportage Replacement Key

For a number of Kia models, the key contains an integrated keyless entry system. This key is similar to an remote control and is exchangeable by an Kia dealer.

Key fobs might stop working due to a number of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some suggestions to assist you in getting your kia picanto key fob replacement sportage replacement key to work again.

How to replace a smartkey or remote key?

No matter if your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder metal key The battery inside these keys will eventually need replacing. This is particularly the case if your car displays a message telling you that the remote or smart keys are in poor condition.

It's a simple process. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover open. Inside the key fob there will be a small screw that holds the battery in its place. With a small screwdriver, take the screw off and pull out the battery that was in place. Insert the new battery and then close the cut on the key fob.

When the key fob is equipped with new batteries Test it by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're all set! You can now make use of the Kia's hands-free lock/unlock feature when your fingers are cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys), do not need programming. If you're looking to reprogramme your key, it is necessary to note the key code number on the tag for the key code.

How do I replace the battery?

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, it is a sign that the battery should be replaced. A low battery could cause other issues, such as the check engine light turning on or delayed engine cranking. Fortunately replacing the key fob battery is a fairly simple DIY task that requires only some basic tools.

Before beginning the process, make sure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece that is located at the bottom of the key fob. Move it until the metal key pops out. The key can be put into the driver door handle to unlock your car.

To replace the battery inside the key fob, you must remove the cover that covers the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then orient the replacement battery in a way that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid bending or damaging the contacts made of metal.

Once the new battery is installed after which you turn the key fob off and then on in the ignition several times until the door locks. You can then test the Kia's key fob to ensure it's functioning properly.

How do I replace a smart keys

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard key fob does not. Both key fobs come with batteries that will eventually require replacement. This is a simple procedure that takes only two minutes.

Before you get started, you will want to ensure that you're on a flat surface with good lighting and that your Kia is turned off. Keep in mind that the fob is made up of tiny pieces that could fall when you're not careful.

The small release button is located on the lower backside. It will be a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is a one called CR-2032 and can be purchased through the internet or at a local auto parts shop. When you are done with the battery, you should be able to lock and unlock your vehicle with your key fob even if the engine isn't running!

How do I replace the mechanical key

The Kia keyfob is an excellent convenience that lets us lock or unlock our car by pressing one button. But like any device it will encounter issues occasionally. Luckily, there are ways to solve these issues and keep our key fobs in good working order in the long run.

A dead or low-quality battery is one of the most common problems. This can cause the fob to stop working completely or to work intermittently. If this is the case you should replace the battery with a fresh new one.

If this isn't enough to resolve the problem then try using a normal flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not damage any internal components, or scratch the plastic. After the battery has been removed, replace it with a new one.

When the new battery is in, shut and open the doors using the mechanical key (every kia rio car key replacement fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's functioning properly. If the key fob isn't functioning, contact a locksmith or dealer to resolve the problem. Make sure they make you an emergency key that can work for all door and trunk cylinders to prevent lockouts in the future.