Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to auto locksmiths with experience who have the right equipment and technical knowledge. They can program and create keys quicker and more efficiently than dealers.

If your key fob stopped locking or unlocking your doors it is likely due to a dead battery in the coin. There are also other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking, and will not allow you to start the engine. In this instance you'll need make use of the alternative method for starting that is described in the owner's manual.

The spark plugs may also be worn out. The spark plugs are responsible for instigating the fuel that ignites the engine. However they are limited in their life span. They'll eventually fail if they're not used enough.

There is a simple solution to this issue. The best way to solve this issue is to measure the voltage of your car battery using a multimeter. If the voltage falls below 11,5 volts, it's time to replace it. It is also essential to clean the contacts of the battery when it has corrosion. This can be done by removing the rubber covers off the two battery terminals and then using a wirebrush, you can remove any damaged parts of the battery. Then, reconnect your cables to connect the positive and negative poles.

Water Damage

If your 208 won't start and the battery isn't flat, then you need to make sure whether the spark plugs are in good working order. It could be that they are dirty and they don't spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with a transponder style key that is compatible with the car's immobiliser system. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, it will not transmit the correct signal to the vehicle.

Water damage is a typical cause of this problem. This is particularly common in colder climates where the vehicle might have been exposed to rain or snow. In this case, you need to contact a reliable locksmith who has the necessary tools and equipment to reprogram the key. They will also have the latest technological know-how and the equipment required to make the Peugeot 208 smart key. The process should not take more than 15 minutes.

Faulty battery contacts

Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that uses electronic components on a circuit board. This new key for peugeot 207 technology works great when it's new, but as time passes, the circuit boards begin to deteriorate and stop working correctly.

This can stop the immobiliser chip activating which means that your car won't start. If this happens it's best to call a Peugeot specialist or locksmith.

A common problem is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars will replace the battery and then cut a new key blade for you. This is a quick fix.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the floor, or being exposed to a sudden downpour or accidently washing it may be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer that controls the central locking system of your Peugeot vehicle.

The rubber seals on the key fob block water from reaching its electronic chip. However, prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. The high salt content of the ocean water or pool could cause damage to the key fob if it is submerged.

If your Peugeot spare key fob stops working You'll need the module replaced. This is only done by an expert auto locksmith or peugeot 208 key fob specialist. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the proper programming to allow the car to start. This is the reason that you should only rely on an authorized Peugeot locksmith to design and program an alternative.

Computer with a problem on board

The on-board computer in your Peugeot is responsible for many of the systems in your car, including airbags and power windows. The computer on board will display an error code when something goes wrong. The code will be stored in the system until the issue is fixed. Most often, this involves replacing the on-board computer.

One of the most frequent causes of the light flashing is loose or corroded connectors in the airbag sensor. This can occur due to wear and tear, aging, or exposure to moisture and salt. This issue needs to be dealt with as soon as you can, since an airbag that is malfunctioning could be dangerous in case of an accident.

If you encounter an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob might be dead or weak. This will stop the key fob from sending a signal to deactivate the immobilizer on your vehicle. Try this by pressing the unlock key on the fob's key, then trying to start your vehicle. If this doesn't work the battery on the key is in need of replacement.